Laserfiche WebLink
Scissor Lift SLX by Draper page 6 of 8 <br />www.draperinc.com (765) 987-7999 <br />Wiring Schematic <br />N <br />U <br /> <br />C <br />D <br />Dashed wiring by electrician <br />11 <br />5 <br />V <br /> <br />a <br />c <br />, <br />Su <br />p <br />p <br />l <br />y <br />Attached to lower pan <br />WH <br />BKBK <br />WH <br />GN <br />WH <br />Low voltage wiring by others <br />Low Voltage Tr igger (6-24 VDC) <br />WH EncoderRD <br />BK <br />RD WH RD <br />WH <br />BK <br />Wall SwitchKey Switch <br />RP/RQ Bus Po rts for <br />remote controls such <br />as IR Eye, RF Receiver, <br />LED Wall Switch and <br />RS232. <br />WH <br />RD <br />BNRDWHBKYL <br />YL/GN <br />RD <br />BKBKOR <br />Up LimitSwitch <br />NC <br />NC <br />RDBNNC <br />Down LimitSwitch <br />Delay Switch <br />(ON position) <br />RD <br />BKBK <br />OR BK <br />BK <br />RD <br />BL <br />YL/GN <br />BK <br />Motor <br />Up <br />Down <br />BK <br />BK <br />BK <br />WH <br />OR <br />RD <br />BK <br />BK <br />WH <br />OR <br />RD <br />AC <br />AC <br />COM <br />N.O. <br />N.C. <br />BK <br />WH <br />RD <br />OR <br />Optional Delay Assembly <br />115V ac, 7A 60 Hz Outlet <br />Run Cap <br />60 MFD <br />2 Cond. Cable <br />RD <br />BKBK <br />OR <br />Up <br />Limit <br />Switch <br />NC <br />NC <br />BK <br />Jumper* <br />ALTERNATE ‘UP’ LIMIT SWITCH WIRING <br />nOte: this CAnnOt be <br />used when lift is installed in <br />environmental Air Space Housing <br />and Optional Ceiling Closure <br />*Black (BK) Jumper wire is <br />located in the plastic sleeve <br />with these instructions. <br />ROTAT ETOADJUST <br />DOWNLimit <br />Switch <br />RRRRRRRROTAT ETTTTTTTOOTTAAAAAAADJAAAAAUST <br />DOWN <br />Adjusting fULLy DOWn position <br />Limit switches for the Scissor Lift SL are preset at the factory. <br />The DOWn limit switch is set for the fully down (maintenance) position <br />for the size lift you have ordered. The limit switch assembly is located <br />inside the lift and behind the Lifting Cable Drum. <br />The Down limit switche shown in the drawing are for setting the "Fully <br />Down" position. This can be adjusted manually by loosening or tightening <br />the screw to increase or reduce the travel. <br /> Caution: The maintenance/service factory limit setting must <br />not be adjusted to a lower position than the preset factory limit <br />setting. In addition, Draper does not recommend setting show <br />position at the maintenance/service position. <br />Adjusting Limit Switches <br />PLEASE NOTE: <br />Changing the fully open or fully closed position will reset the electronic controls and cause the lift to operate improperly. <br />Please call Draper before attempting these adjustments. <br />Figure 8