Laserfiche WebLink
DRAPER SALESPERSON: <br />CUSTOMER CONTACT: <br />SIGNATURE: (765) 987-7999www.draperinc.com <br />Scissor Lift Submittal & Planning Sheet for SLX Series page 4 of 4 <br />Wiring Diagram <br />N <br />U <br /> <br />C <br />D <br />Dashed wiring by electrician <br />11 <br />5 <br />V <br /> <br />a <br />c <br />, <br />Su <br />p <br />p <br />l <br />y <br />Attached to lower pan <br />WH <br />BKBK <br />WH <br />GN <br />WH <br />Low voltage wiring by others <br />Low Voltage Tr igger (6-24 VDC) <br />WH EncoderRD <br />BK <br />RD WH RD <br />WH <br />BK <br />Wall SwitchKey Switch <br />RP/RQ Bus Po rts for <br />remote controls such <br />as IR Eye, RF Receiver, <br />LED Wall Switch and <br />RS232. <br />WH <br />RD <br />BNRDWHBKYLYL/GN <br />RD <br />BKBKOR <br />Up LimitSwitch <br />NC <br />NC <br />RDBNNC <br />Down LimitSwitch <br />Delay Switch <br />(ON position) <br />RD <br />BKBK <br />OR BK <br />BK <br />RD <br />BL <br />YL/GN <br />BK <br />Motor <br />Up <br />Down <br />BK <br />BK <br />BK <br />WH <br />OR <br />RD <br />BK <br />BK <br />WH <br />OR <br />RD <br />AC <br />AC <br />COM <br />N.O. <br />N.C. <br />BK <br />WH <br />RD <br />OR <br />Optional Delay Assembly <br />115V ac, 7A 60 Hz Outlet <br />Run Cap60 MFD <br />2 Cond. Cable <br />KE <br />Y <br />WA <br />L <br />L <br />RP <br />/ <br />R <br />Q <br />RP <br />/ <br />R <br />Q <br />LV <br />T <br />Red - Down <br />Black - Com <br />Black - Com <br />Blue - Up <br />Pin 3 - Green <br />Pin 2 - Yellow <br />Pin 5 - Black <br />DCU <br />Green - DOWN <br />Black - COM <br />Yellow - UP <br />PIN <br />1 - NOT USED <br />2 - YELLOW <br />3 - GREEN <br />4 - NOT USED <br />5 - BLACK <br />6 - NOT USED <br />Please Note: <br />Data cable connections must <br />be made using electrically <br />straight 6 Pin 4 conductor <br />modular cable (RJ14/6P4C). <br />Please Note: <br />RJ14/6P4C <br />Data Cables <br />for Serial Control <br />Provided by Others <br />SP-KSMKey SwitchService Position <br />Optional R2D7, <br />RS232 Controller <br />RP/RQ Bus Ports for remote controlssuch as IR Eye, RF Receiver, LED Wall Switch and RS232. <br />LVC-SShow Position <br />Low Voltage Trigger <br />(6-24 VDC) <br />(Polarity Independent) <br />Function <br />Indicator <br />To RS232 Serial Port:1 - Blue = Not Used2 - Yellow = Rx (Data from control system)3 - Green = Tx (Data to control system)4 - Red = Not Used5 - Black = Gnd (Signal Ground)6 - White = Not Used <br />DETAIL OF DATA CABLE <br />SPLITTER BOARD <br />AutomatedDry Contact System <br />Connecting Controls to Data Cable Splitter Board <br />Controls plug into the Data Cable Splitter Board (See diagram below) which is located on the Top Frame on the front side of the lift, using RJ14/6P4C connectors. <br />For IR or RF Remote Control, use data cable <br />with RJ14/6P4C connectors on both ends. <br />For serial control of "Show" position, <br />use data cable with RJ14/6P4C connectors <br />on both ends and an R2D7 Serial Control <br />Interface. Plug into the "RP/RQ" input. <br />Please Note:Any control, including automated dry contact systems, being connected to the wall switch input MUST send a momentary signal.