Addendum # 1 City of Sunny Isles Response-RFI Sheet

Home Browse Search

K-6710WHITBYC_SINKSCAST IRON K-6710WHITBYC_SINKSCAST IRON13 24 KEY NOTES: 1.COORDINATE AND LOCATE THE NEW SOLID INTERCEPTOR (SCHIER #SI-500 OR EQUAL) UPSTREAM OF THENEW GREASE INTERCEPTOR (SCHIER #GB-1000 OR EQUAL), PRIOR TO COMMENCING WORK TO COMPLY WITHD.E.R.M. REQUIREMENTS. THE BUILDINGS EXISTING GREASE WASTE LINE SHALL BE EXTENDED AND CONNECTTO THE NEW INTERCEPTORS (VIF). INSTALL PER MANUFACTURE INSTALLATION INSTRUCTIONS AND DETAIL #1ON SHEET.2.EXTEND AND CONNECT THE EXISTING 6" GREASE WASTE PIPING TO THE NEW 6" GREASE WASTE LINE ASREQUIRED TO COMPLETE THE RENOVATION PHASE OF THE PROJECT. FIELD VERIFY THE EXISTING I.E. = +2'-1".3.CONTRACTOR SHALL PROVIDE AND LOCATE THE SAMPLING PORT BETWEEN THE NEW GREASE INTERCEPTORAND THE EXISTING LAST TWO-WAY CLEAN-OUT.4.CONTRACTOR SHALL PROVIDE AN ALLOWANCE FOR DE-WATER TO ALLOW FOR THE INSTALLATION OF THENEW GREASE INTERCEPTOR AND THE NEW SOLIDS INTERCEPTOR. DRAWING LEGEND: ·ALL PIPING THAT IS SHOWN IS BELOW SLAB UNLESS NOTED OTHERWISE.·CONTRACTOR SHALL LOCATE THE NEW SOLID AND GREASE INTERCEPTOR IN THE LOCATION OF THE LAST DEMOLISHEDCONCRETE GREASE TRAP. COORDINATE IN THE FIELD PRIOR TO COMMENCING WORK.·CONTRACTOR SHALL COORDINATE ALL NEW WORK WITH EXISTING UTILITIES IN FIELD PRIOR TO CONSTRUCTION. NOTIFY E.O.R.OF ANY DISCREPANCIES.·INSTALLATION OF ALL GAS PIPING SHALL BE PER F.B.C. FUEL GAS 2023 (GAS PIPING (STANDARD)·REFER TO RISER FOR PIPE MATERIALS.·PRESSURE TEST GAS PIPING FOR LEAKS PRIOR TO CONNECTING GAS SUPPLY.·PLEASE VERIFY MANUFACTURES REQUIREMENTS FOR BTU DEMAND, MINIMUM AND MAXIMUM GAS PRESSURE LIMITS ATEQUIPMENT. PRESSURE REGULATOR IF REQUIRED MUST BE APPROVED BY EQUIPMENT MANUFACTURE.·VERIFY LOCATION OF EQUIPMENT PRIOR TO INSTALLATION.·ALL CONDUITS ENCASING GAS PIPE BELOW SLAB SHALL BE VENTED MINIMUM 6" ABOVE GRADE AND SHALL BE INSTALLED SOAS TO PREVENT THE ENTRY OF WATER & INSECTS.·GAS PIPE SHALL REQUIRE INSULATED METALLIC LOCATING WIRE (14 GAUGE COPPER AGAVE WIRE) CAPABLE OF DETECTIONBY A CABLE LOCATOR AND SHALL BE BURIED DIRECTLY ABOVE THE CENTERLINE OF THE PIPE. USE FGG/BM COMPATIBLEDUCT TAPE AS NECESSARY TO HOLD WIRE DIRECTLY ON THE TOP OF THE PIPE.·PE PIPE INSTALLED BELOW HARD SURFACE, "SLAB" MUST BE SLEEVED AND VENTED.·COORDINATE THE LOCATION OF THE NEW GAS LINE & METER WITH THE GENERAL CONTRACTOR AND SITE UTILITY PROVIDER.·THE ENTIRE EXISTING GREASE WASTE LINE SHALL BE JETTED BACK TO THE EXISTING GREASE INTERCEPTOR LOCATIONS ASREQUIRED TO CONFIRM ITS FUNCTIONALITY.GENERAL NOTESPOINT OF NEW CONNECTIONSHUT-OFF VALVEGAS TO FIXTUREGAS PRESSURE REGULATORGAS SOLENOID VALVE2 PSI PIPE SIZING PER F.B.C. 2023 FUEL GAS - TABLE 402.4(5) & 402.4(18)2,115 CFH @ 30'-0" LENGTHGAS PIPE SIZINGDETAILNO. 1SOLIDS INTERCEPTOR & GREASE INTERCEPTOR INSTALLATION DETAILFOG NOTES:Plumbing Site PlanP100PLUMBING SITE PLANSCALE: 3/16" = 1'-0"Nhttp://www.beai.com PHONE: (305) 461-2053 LICENSE No. AA26001612 Miami, Florida 33168 11575 Northwest 7 Avenue FAX: (305) 634-0599 E-mail: info@beai.com BEA architects Inc. © a r c h i t e c t s CITY OF SUNNY ISLES BEACH 18050 COLLINS AVENUE, SUNNY ISLES BEACH, FLORIDA 3316021-1011BUILDING DEPARTMENT RELOCATION TO ANNEX02-14-2025BID SETwww.hammondengineers.com499 N.W. 70thAvenue,Suite 215Plantation, Florida 33317THIS ITEM HAS BEEN DIGITALLY SIGNED AND SEALED BY JOHN GRAY CUMPER ON THE DATE ADJACENT TO THE SEAL. PRINTED COPIES OF THIS DOCUMENT ARE NOT CONSIDERED SIGNED AND SEALED AND THE SIGNATURE MUST BE VERIFIED ON ANY ELECTRONIC COPIES.