Laserfiche WebLink
<br />..., <br /> <br />. <br /> <br />..., <br /> <br /> Irype HV Type HSHV <br />Confined Tension 2,290 psi [15.8 MPa] 3,060 psi [21.1 Mpa] <br />Damp-Hole Installation 1,680 psi [11.6 MPa] 1,830 psi [12.6 Mpa] <br />Elevated Temperature 2,290 psi [15.8 MPa] 3,060 psi [21.1 Mpa] <br />Horizontal Orientation 2,060 psi [14.2 MPa] 2,060 psi [14.2 Mpa] <br />Short Term Cure 1,710 psi [11.8 MPa] 1,710 psi [11.8 Mpa] <br />Specified Bond Strength 1,080 psi [7.5 MPa] 1,830 psi [12.6 Mpa] <br /> <br />- <br /> <br />II <br /> <br />. <br /> <br />..., <br />. <br /> <br />-, <br />. <br /> <br />Maximum Coefficient Of Variation for Uniform Bond Stress ................................. 20% <br /> <br />.... <br /> <br />Long Term Load (Creep): <br />(1) The rate of displacement shall decrease during the 42 day application of <br /> <br />. <br /> <br />load. <br /> <br />...., <br /> <br />(2) At 42 days the total displacement due to creep (with load still applied) <br />shall be less than 0.03 inch [0.75 mm] and during the last 14 days of the 42 day load <br />duration, the total displacement due to creep shall be less than 0.003 inch [0.075 mm]. <br />(3) After removal of the 42 day load, the uniform bond Stress from a <br />subsequent Confined Tension Test shall not be less than 1,826 psi [12.6 MPa]. <br /> <br />. <br /> <br />.., <br /> <br />. <br /> <br />,.., <br /> <br />937-5 Product Identification (Fingerprint) Properties (FM 5-569). <br />References for comparison including Infrared Absorption, Density or Average <br />Weight, Gel Time or Setting Time, and Bond Strength shall be determined in accordance <br />with FM 5-569. <br /> <br />. <br /> <br />-, <br /> <br />.... <br /> <br />937-6 Packaging and Marking. <br />The adhesive bonding material system shall be delivered to the project site in <br />original unopened containers with the manufacturer's label identifying the product. Each <br />package shall be clearly marked with the following information: <br />Manufacturer's name and address <br />Product Name <br />Date of Manufacture <br />Expiration Date <br />LOT Identification Number <br />Storage and Handling Requirements <br />Each package shall include the manufacturer's instructions for anchor and dowel <br />installation. The instructions shall include the following information: <br />Diameters of drilled holes for applicable anchor and dowel sizes. <br />Cleaning procedure for drilled holes, including a description of permitted and <br />prohibited equipment and techniques. <br />Allowable temperature ranges for storage, installation and curing. <br />Identification of acceptable mixing/dispensing nozzles. <br />Fabrication requirements for anchors and dowels. <br />Description of tools permitted or required for installation. <br />Method of identifying properly proportioned and mixed adhesive materials. <br />Time and temperature schedule for initial set and full-strength cure. <br />Special requirements for special installation conditions such as damp holes, <br />or horizontal or near horizontal orientation of the anchor or dowel. <br /> <br />. <br /> <br />..., <br /> <br />. <br /> <br />..., <br /> <br />. <br /> <br />. <br /> <br />.., <br /> <br />. <br /> <br />..., <br /> <br />- <br /> <br />..., <br /> <br />. <br /> <br />.., <br /> <br />. <br /> <br />-, <br /> <br />. <br /> <br />09/09 <br /> <br />01 000-1 80 <br /> <br />03-4122.F <br /> <br />..... <br /> <br />. <br />