Laserfiche WebLink
HD-EXT-USB-2000-C 4K HDMI® & USB over HDBaseT® Extender 2000 <br />crestron.com | 800.237.2041 <br />Digital Formats: Dolby Digital®, Dolby Digital EX, Dolby Digital Plus, <br />Dolby TrueHD, Dolby Atmos, DTS®, DTS-ES, DTS 96/24, DTS-HD High Res, <br />DTS-HD Master Audio, LPCM up to 8 channels <br />Analog Formats: Stereo 2-channel <br />Analog-To-Digital Conversion: 24-bit 48 kHz <br />Digital-To-Analog Conversion: 24-bit 48 kHz <br />Analog Performance: <br />Frequency Response: 20 Hz to 20 kHz ±0.5 dB; <br />S/N Ratio: >95 dB, 20 Hz to 20 kHz A-weighted; <br />THD+N: <0.005% @ 1 kHz; <br />Stereo Separation: >80 dB, 20 Hz to 20 kHz <br />Communications <br />Ethernet: 10/100 Mbps pass-through <br />USB: USB 2.0 pass-through (also supports firmware update via USB mass <br />storage device at TX) <br />RS-232: 2-way serial pass-through up to 115.2k baud (TD/RD only) <br />IR: Bidirectional IR signal pass-through up to 60 kHz <br />HDMI: HDCP 2.2, EDID, CEC pass-through <br />HDBaseT: HDCP 2.2, EDID, PoE+, Ethernet, IR/RS-232 (intended for signal <br />extension between TX & RX only) <br />Connectors – Transmitter (HD-TX-USB-2000-C) <br />HDMI IN: (1) HDMI Type A connector, female; <br />HDMI digital video/audio input; <br />(DVI & Dual-Mode DisplayPort compatible [2]) <br />AUDIO IN: (1) 3.5 mm TRS mini phone jack & (1) 5-pin 3.5 mm detachable <br />terminal block; Balanced or unbalanced stereo line-level audio input [3]; <br />Maximum Input Level: 4 Vrms balanced, 2 Vrms unbalanced; <br />Input Impedance: 10k Ohms balanced, 5k Ohms unbalanced; <br />Note: The TRS jack is unbalanced stereo and paralleled with the L+ (tip), <br />R+ (ring), and ground (sleeve) terminals; only one audio input connection <br />should be used; this input signal supplants the HDMI audio input signal <br />when selected <br />USB (host): (1) USB Type A connector, female; USB 2.0 host port for <br />connection of a mouse, keyboard, or any other USB 2.0 peripheral device [5]; <br />Passes USB data to/from the USB device port on the RX when in <br />DEVICE mode; <br />Available Power: 1 Amp at 5 Volts DC <br />USB (device): (1) USB Type Micro-B connector, female; USB 2.0 device port <br />for connection to a computer or any other USB 2.0 host [5]; <br />Passes USB data to/from the USB host port on the RX when in HOST mode <br />LAN: (1) 8-pin RJ45 connector, female; <br />10Base-T/100Base-TX Ethernet port; <br />Passes Ethernet data to/from the LAN port on the RX <br />COM: (1) 3.5 mm TRS mini phone jack & (1) 3-pin 3.5 mm detachable <br />terminal block; Bidirectional RS-232 port; <br />Passes RS-232 TD/RD data to/from the COM port on the RX; <br />Supports up to 115.2k baud <br />Note: The TRS jack and terminal block are paralleled; only one should <br />be used <br />IR IN: (1) 3.5 mm TS mini phone jack & (1) 2-pin 3.5 mm detachable <br />terminal block; IR input port for connection from a Crestron IR control port <br />or other IR signal source; <br />Passes IR signal to the IR OUT port on the RX; <br />Supports IR up to 60 kHz; <br />Note: The TS jack and terminal block are paralleled; only one should <br />be used <br />HDBT OUT: (1) 8-pin RJ45 connector, female, shielded; HDBaseT and PoE <br />Class 3 PD port for connection to the HDBT IN port on the RX [1] <br />HD-TX-USB-2000-C Transmitter – Top, Front, and Bottom Views <br />HD-RX-USB-2000-C Receiver – Top, Front, and Bottom Views