Laserfiche WebLink
HD-EXT-USB-2000-C 4K HDMI® & USB over HDBaseT® Extender 2000 <br />crestron.com | 800.237.2041 <br />IR OUT: (1) 3.5 mm TS mini phone jack & (1) 2-pin 3.5 mm detachable <br />terminal block; IR output port for connection to an IR emitter; <br />Passes IR signal from the IR IN port on the RX; <br />Supports IR up to 60 kHz; <br />Note: The TS jack and terminal block are paralleled; only one should <br />be used <br />Connectors – Receiver (HD-RX-USB-2000-C) <br />HDMI OUT: (1) HDMI Type A connector, female; <br />HDMI digital video/audio output (DVI compatible [2]) <br />AUDIO OUT: (1) 3.5 mm TRS mini phone jack & (1) 5-pin 3.5 mm <br />detachable terminal block; <br />Balanced or unbalanced stereo line-level audio output [4]; <br />Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced; <br />Output Impedance: 499 Ohms balanced or unbalanced; <br />Note: The TRS jack is unbalanced stereo and paralleled with the L+ (tip), <br />R+ (ring), and ground (sleeve) terminals <br />USB (host): (1) USB Type A connector, female; USB 2.0 host port for <br />connection of a mouse, keyboard, or any other USB 2.0 peripheral device [5]; <br />Passes USB data to/from the USB device port on the TX when in <br />HOST mode; <br />Available Power: 1 Amp at 5 Volts DC <br />USB (device): (1) USB Type Micro-B connector, female; USB 2.0 device port <br />for connection to a computer or any other USB 2.0 host [5]; <br />Passes USB data to/from the USB host port on the TX when in <br />DEVICE mode <br />LAN: (1) 8-pin RJ45 connector, female; <br />10Base-T/100Base-TX Ethernet port; <br />Passes Ethernet data to/from the LAN port on the TX <br />COM: (1) 3.5 mm TRS mini phone jack & (1) 3-pin 3.5 mm detachable <br />terminal block; Bidirectional RS-232 port; <br />Passes RS-232 TD/RD data to/from the COM port on the TX; <br />Supports up to 115.2k baud <br />Note: The TRS jack and terminal block are paralleled; only one should <br />be used <br />IR IN: (1) 3.5 mm TS mini phone jack & (1) 2-pin 3.5 mm detachable <br />terminal block; IR input port for connection from a Crestron IR control port <br />or other IR signal source; <br />Passes IR signal to the IR OUT port on the TX; <br />Supports IR up to 60 kHz; <br />Note: The TS jack and terminal block are paralleled; only one should <br />be used <br />HDBT IN: (1) 8-pin RJ45 connector, female, shielded; HDBaseT and PoE+ <br />PSE port for connection to the HDBT OUT port on the TX [1] <br />IR OUT: (1) 3.5 mm TS mini phone jack & (1) 2-pin 3.5 mm detachable <br />terminal block; IR output port for connection to an IR emitter; <br />Passes IR signal from the IR IN port on the TX; <br />Supports IR up to 60 kHz; <br />Note: The TS jack and terminal block are paralleled; only one should <br />be used <br />24VDC 1.25A: (1) 2.1 x 5.5 mm DC power connector; <br />24 Volt DC power input; <br />PW-2412WU power pack included; <br />Note: This connection powers both the receiver and transmitter <br />Controls & Indicators – Transmitter <br />(HD-TX-USB-2000-C) <br />POWER: (1) Bi-color green/amber LED, indicates operating power is <br />supplied via the HDBaseT link to the companion receiver, turns amber <br />while booting and green when operating <br />HDMI IN: (1) Green LED, indicates HDMI input signal presence <br />LINK: (1) Bi-color green/amber LED, green indicates an HDBaseT link <br />with video, amber indicates a link without video <br />AUDIO SEL HDMI/ANALOG: (1) 2-position slide switch, selects the <br />audio input [3] <br />RESET: (1) Recessed pushbutton, initiates hardware reset of both the <br />transmitter and receiver <br />LAN: (2) LEDs, green LED indicates Ethernet link status, amber LED <br />indicates Ethernet activity <br />HDBT OUT: (2) LEDs, amber LED indicates HDBaseT link status, green <br />LED indicates PoE <br />Controls & Indicators – Receiver (HD-RX-USB-2000-C) <br />POWER: (1) Bi-color green/amber LED, indicates operating power is <br />supplied from the power pack via the 24VDC input, turns amber while <br />booting and green when operating <br />HDMI OUT: (1) Green LED, indicates HDMI output signal presence <br />LINK: (1) Bi-color green/amber LED, green indicates an HDBaseT link with <br />video, amber indicates a link without video <br />HOST/AUTO/DEVICE: (1) 3-position slide switch, selects the USB mode [5] <br />LAN: (2) LEDs, green LED indicates Ethernet link status, amber LED <br />indicates Ethernet activity <br />HDBT IN: (2) LEDs, amber LED indicates HDBaseT link status, green <br />LED indicates PoE <br />Power <br />Power Pack (included): <br />Input: 0.8 Amps (maximum) @ 100-240 Volts AC, 50/60 Hz; <br />Output: 1.25 Amps @ 24 Volts DC; <br />Model: PW-2412WU <br />Power Consumption: 18.7 Watts typical <br />Environmental <br />Temperature: 32° to 104° F (0° to 40° C) <br />Humidity: 20% to 90% RH (non-condensing) <br />Heat Dissipation: 63.8 BTU/hr <br />Construction – Typical of Transmitter & Receiver <br />Chassis: Metal, black finish, with (2) integral mounting flanges, vented sides <br />Mounting: Freestanding, surface mount, or attach to a single rack rail