Laserfiche WebLink
DM-TX-4K-100-C-1G Wall Plate 4K DigitalMedia 8G+® Transmitter 100 <br />crestron.com | 800.237.2041 <br />MODELS & ACCESSORIES <br />Available Models <br />DM-TX-4K-100-C-1G-B-T: Wall Plate 4K DigitalMedia 8G+® Transmitter <br />100, Black Textured <br />DM-TX-4K-100-C-1G-W-T: Wall Plate 4K DigitalMedia 8G+® Transmitter <br />100, White Textured <br />Included Accessories <br />PW-2407WUL: Wall Mount Power Pack, 24VDC, 0.75A, Flying Leads, <br />Universal (Qty. 1 included) <br />Available Accessories <br />DM-PSU-ULTRA-MIDSPAN: DigitalMedia™ Ultra Midspan PoDM++ Injector <br />DM-CBL-ULTRA-PC: DigitalMedia™ Ultra Patch Cables <br />DM-CONN-ULTRA-RECP: DigitalMedia™ Ultra Keystone RJ45 Jack <br />DM-CBL-ULTRA-NP: DigitalMedia™ Ultra Cable, Non-Plenum Type CMR <br />DM-CBL-ULTRA-P: DigitalMedia™ Ultra Cable, Plenum Type CMP <br />DM-CBL-ULTRA-LSZH: DigitalMedia™ Ultra Cable, Low Smoke Zero <br />Halogen (Available only in Europe) <br />DM-CONN: Connectors for DM-CBL-ULTRA DigitalMedia Ultra Cable <br />DM-CBL-8G-NP: DigitalMedia 8G™ Cable, non-plenum <br />DM-CBL-8G-P: DigitalMedia 8G™ Cable, plenum <br />DM-8G-CONN: Connectors for DM-CBL-8G DigitalMedia 8G™ Cable <br />DM-8G-CRIMP: Crimping Tool for DM-8G-CONN <br />DM-8G-CONN-WG: Connectors with Wire Guide for DM-CBL-8G <br />DigitalMedia 8G™ Cable <br />DM-8G-CRIMP-WG: Crimping Tool for DM-8G-CONN-WG <br />CBL Series: Crestron® Certified Interface Cables <br />CNSP-XX: Custom Serial Interface Cable <br />IRP2: IR Emitter Probe w/Terminal Block Connector <br />MP-WP183: Media Presentation Wall Plate - Ethernet <br />Notes: <br />1. The IR and RS-232 (COM) ports are only enabled when the DM-TX-4K-100-C-1G is <br />connected to an Ethernet-enabled DM transmitter or switcher that is addressable from a <br />Crestron control system. <br />2. The maximum cable length for DigitalMedia 8G+ (DM 8G+) or HDBaseT is dependent upon <br />the type of cable and resolution of the video signal. Refer to the “Maximum Cable Lengths” <br />table for a detailed overview. Crestron legacy cable models DM-CBL DigitalMedia Cable and <br />DM-CBL-D DigitalMedia D Cable support the same resolutions and cable lengths as CAT5e. <br />Shielded cable and connectors are recommended to safeguard against unpredictable <br />environmental electrical noise which may impact performance at resolutions above 1080p. <br />Refer to the Crestron DigitalMedia Design Guide, Doc. #4546 for complete system design <br />guidelines. DM 8G+ is compatible with HDBaseT Alliance specifications for connecting to <br />HDBaseT compliant equipment. All wire and cables are sold separately. <br />3. The DM-TX-4K-100-C-1G does not include an Ethernet port. Local Ethernet connectivity for <br />external devices requires a MP-WP183 or equivalent Ethernet jack with a dedicated LAN <br />connection. <br />4. The HDMI input requires an appropriate adapter or interface cable to accommodate a DVI or <br />Dual-Mode DisplayPort signal. CBL-HD-DVI interface cables are available separately. <br />5. To power the DM-TX-4K-100-C-1G using PoDM (Power over DigitalMedia) requires <br />connection to a DM switcher or other equipment that has a PoDM PSE port. Any wiring that is <br />connected to a PoDM PSE port is for intra-building use only and should not be connected to a <br />line that runs outside of the building in which the PSE is located. <br />6. To power the DM-TX-4K-100-C-1G using HDBaseT PoE requires connection to a switcher <br />or other equipment that has an HDBaseT PoE PSE port. Any wiring that is connected to an <br />HDBaseT PoE PSE port is for intra-building use only and should not be connected to a line that <br />runs outside of the building in which the PSE is located. <br />7. Supports simple pass-through of CEC when connected directly to a DM-RMC-4K-100-C-1G <br />receiver. Supports full management of CEC between the locally connected HDMI device and a <br />control system when connected to an Ethernet-enabled 4K DM receiver or switcher that <br />supports CEC over HDBaseT. Refer to the spec sheet for each DM receiver, switcher, input <br />card, or input blade to verify “CEC” is listed under “HDBaseT” in the “Communications” section <br />of the product’s specifications. <br />This product may be purchased from an authorized Crestron dealer. To find a dealer, please <br />contact the Crestron sales representative for your area. A list of sales representatives is available <br />online at www.crestron.com/salesreps or by calling 800-237-2041. <br />The specific patents that cover Crestron products are listed online at: patents.crestron.com. <br />Certain Crestron products contain open source software. For specific information, please visit <br />www.crestron.com/opensource. <br />Crestron, the Crestron logo, DigitalMedia, DigitalMedia 8G, DigitalMedia 8G+, DM, DM 8G, and <br />DM 8G+ are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United <br />States and/or other countries. Dolby, Dolby Atmos, and Dolby Digital are either trademarks or <br />registered trademarks of Dolby Laboratories in the United States and/or other countries. DTS, <br />DTS-HD, and DTS-HD Master Audio are either trademarks or registered trademarks of DTS, Inc. <br />in the United States and/or other countries. HDBaseT and the HDBaseT Alliance logo are either <br />trademarks or registered trademarks of the HDBaseT Alliance in the United States and/or other <br />countries. HDMI and the HDMI Logo are either trademarks or registered trademarks of HDMI <br />Licensing LLC in the United States and/or other countries. Other trademarks, registered trade- <br />marks, and trade names may be used in this document to refer to either the entities claiming the <br />marks and names or their products. Crestron disclaims any proprietary interest in the marks and <br />names of others. Crestron is not responsible for errors in typography or photography. <br />Specifications are subject to change without notice. ©2016 Crestron Electronics, Inc.