Laserfiche WebLink
<br />.., <br /> <br />. <br /> <br />n <br /> <br />., <br /> <br />Ensure the test container is suitable for testing the following steel surfaces: <br />horizontal (up/down configuration), vertical, flat, curved, smooth, pitted, and rough. <br />Ensure the kit uses a test container, with resulting ion extract solution, as <br />the titration container. <br />Ensure the Ion concentrations are directly measured In micrograms per <br />square centimeter without using either conversion charts or tables. <br />560-2.5 Abrasives: Use abrasive materials that meet the requirements of <br />SSPC-AB 1, Mineral and Slag Abrasives, SSPC-AB 2, Cleanliness of Recycled Ferrous <br />Metallic Abrasives, or SSPC-AB 3, Newly Manufactured or Re-Manufactured Steel Abrasive <br />and do not introduce any contamination that interferes with the coating application and <br />performance. <br />Provide certification to the Engineer that the abrasives used do not contain <br />any chlorides and other salts. <br />Ensure recycled abrasive meets all requirements of this Specification each <br />time it is placed in the blast pot. <br />560-2.6 Rust Preventative Compound: Use a rust preventative compound that <br />meets the requirements of Federal Standard TP 664. <br /> <br />. <br /> <br />,.., <br /> <br />. <br /> <br />..., <br />. <br /> <br />. <br /> <br />,., <br /> <br />. <br /> <br />., <br />. <br /> <br />I' <br /> <br />. <br /> <br />560-3 Equipment. <br />560-3.1 Compressed Air: Use a compressed air system capable of delivering clean, <br />dry, continuous nozzle pressure to achieve the required surface cleanliness and profile or <br />spray pattern. The system must comply with the instructions and recommendations of the <br />manufacturer of the abrasive blasting system or coating application system. <br />560-3.2 Abrasive Blasting System: Design the blasting system to produce the <br />specified cleanliness and profile. <br />560-3.3 Coating Application System: Use the coating application equipment <br />approved by and in accordance with the Coating Manufacturer's technical data <br />requirements. <br /> <br />.., <br />. <br /> <br />.., <br />. <br /> <br />'1 <br />. <br /> <br />,.., <br /> <br />560-4 Environmental, Health and Safety Requirements. <br />Isolate the work areas with containment devices canvasses, tarpaulins or screens, <br />during all cleaning and coating operations. Dispose of all debris and waste products <br />generated in accordance with all Federal, State and Local regulations. Requirements for <br />lead abatement are covered in 560-1 6. <br /> <br />. <br /> <br />.., <br /> <br />. <br /> <br />,.., <br /> <br />560-5 Quality Assurance. <br />Develop a QC plan in accordance with Specification 105. Ensure that all inspection <br />equipment is maintained, calibrated and in good working condition. Furnish and erect <br />scaffolding to the satisfaction of the Engineer to facilitate safe inspection of all surface <br />preparation and coating application. Ensure that all activities are observed and approved by <br />a coatings inspector. <br /> <br />. <br /> <br />,.., <br /> <br />. <br /> <br />,., <br /> <br />560-6 Personnel Qualifications. <br />Provide documentation to the Engineer that all personnel performing surface <br />preparation or coating application are certified by the American Institute of Steel <br />Construction (AISC) Sophisticated Paint Endorsement or the Society for Protective <br />Coatings (formerly Steel Structures Painting Council) (SSPC) to the requirements of SSPC <br /> <br />. <br /> <br />II <br /> <br />. <br /> <br />..., <br /> <br />. <br /> <br />..., <br /> <br />09/09 <br /> <br />01000-129 <br /> <br />03-4122.F <br /> <br />. <br />